Lexmark C750 5060-0XX Service Manual.Pdf

PDF Preview :

How to use this parts catalog
•
SIMILAR ASSEMBLIES: If two assemblies contain a majority of identical parts, they are shown
on the same list. Common parts are shown by one index number. Parts peculiar to one or the
other of the assemblies are listed separately and identified by description.
•
NS: (Not Shown) in the Asm–Index column indicates that the part is procurable but is not
pictured in the illustration.
•
PP: (Parts Packet) in the Description column indicates the part is contained in a parts packet.
The Lexmark C750 (5060-0xx) laser printer is available in two models:
•
5060-001
5060-002
The parts catalog uses these designations to identify model specific FRUs

Comments may be addressed to Lexmark International, Inc., Department D22A/032-2, 740 West New Circle Road,
Lexington, Kentucky 40550, U.S.A or e-mail at ServiceInfoAndTraining@Lexmark.com. Lexmark may use or distribute any
of the information you supply in any way it believes appropriate without incurring any obligation to you. You can purchase
additional copies of publications related to this product by calling 1-800-553-9727. In other countries, contact your point of
purchase.
Lexmark, Lexmark with diamond design, MarkNet, and Prebate are trademarks of Lexmark International, Inc., registered in
the United States and/or other countries. Optra Forms is a trademark of Lexmark International, Inc

Download Free ebook Lexmark C750 5060-0XX Service Manual.Pdf

PIXMA iP5200 PIXMA iP5200R SERVICE MANUAL.Pdf

PDF Preview :

I. MANUAL OUTLINE
This Printer service manual consists of the following three parts to provide information necessary to service the PIXMA iP5200:

Part 1: Maintenance
Information on maintenance and troubleshooting of the PIXMA iP5200
Part 2: Technical Reference
New technology and technical information such as FAQ's (Frequently Asked Questions) of the PIXMA
iP5200
Part 3: Appendix
Block diagrams and pin layouts of the PIXMA iP5200
Reference:
This manual does not provide sufficient information for disassembly and reassembly procedures.
Refer to the graphics in the separate Parts Catalog


II. TABLE OF CONTENTS
Part 1: MAINTENANCE
1. MAINTENANCE
1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by
Service Engineer
1-2. Customer Maintenance
1-3. Product Life
1-4. Special Tools
1-5. Serial Number Location
2. LIST OF ERROR DISPLAY / INDICATION
2-1. Operator Call Errors
2-2. Service Call Errors
2-3. Warnings
2-4. Troubleshooting by Symptom

3. REPAIR
3-1. Notes on Service Part Replacement (and Disassembling / Reassembling)
3-2. Special Notes on Repair Servicing
3-3. Adjustment / Settings
(1) Paper feed motor adjustment
(2) Grease application
(3) Waste ink counter setting
(4) User mode
(5) Service mode
Destination settings
LF correction
3-4. Verification Items
(1) Service test print
(2) EEPROM information print
4. PRINTER TRANSPORTATION

Part 2: TECHNICAL REFERENCE
1. NEW TECHNOLOGIES
2. CLEANING MODE AND AMOUNT OF INK PURGED
3. PRINT MODE
4. FAQ (Problems Specific to the iP5200 and Corrective Actions)

Part 3: APPENDIX
1. BLOCK DIAGRAM
2. CONNECTOR LOCATION AND PIN LAYOUT
2-1. Logic Board Ass'y
2-2. Carriage Board (Print Head Connector)
PIXMA iP5200 Specifications


Download Free ebook PIXMA iP5200 PIXMA iP5200R SERVICE MANUAL.Pdf

HP LaserJet P2015 Series User Guide.Pdf

PDF Preview :

Table of contents

1 Product information
Product features ................................................................................................................................... 2
HP LaserJet P2015 printer .................................................................................................. 2
HP LaserJet P2015d printer ................................................................................................ 2
HP LaserJet P2015n printer ................................................................................................ 3
HP LaserJet P2015dn printer .............................................................................................. 3
HP LaserJet P2015x printer ebook................................................................................................. 3
Identify product parts ............................................................................................................................ 4
2 Control panel
3 Product software
Supported operating systems ............................................................................................................. 10
Printer connections ............................................................................................................................. 11
USB connections ............................................................................................................... 11
Network connections ......................................................................................................... 11
Connect the printer to the network .................................................................... 11
Install the printer software for the network printer ............................................. 12
Software for Windows ........................................................................................................................ 13
Windows printer drivers ..................................................................................................... 13
Windows driver types ........................................................................................ 13
Install the Windows printer software ................................................................. 13
To install printer software for Windows XP (64-bit) and Windows
Server 2003 ...................................................................................... 13
To install printer software for Windows 98 (driver only), Me (driver
only), 2000, and XP (32–bit) ............................................................. 13
Configure the Windows printer driver ................................................................ 13
HP ToolboxFX ................................................................................................................... 14
Embedded Web server ...................................................................................................... 14
Software for Macintosh ....................................................................................................................... 15
Macintosh printer drivers ................................................................................................... 15
Install the Macintosh printer driver .................................................................... 15
Configure the Macintosh printer driver .............................................................. 15
PostScript Printer Description files (PPDs) ........................................................................ 16
4 Supported paper and other media
Optimize print quality for media types ................................................................................................ 18
Guidelines for using media ................................................................................................................. 19
HP media ........................................................................................................................... 19
ENWW

Product features
The following are the standard configurations for the HP LaserJet P2015 Series printers.
HP LaserJet P2015 printer
●
27 ppm (Letter-size), 26 ppm (A4–size)
●
First page out in as few as 8.5 seconds
●
ProRes 1200 (provides fine-line detail at 1200 x 1200 dpi)
●
600 dpi (provides 600 x 600 dpi output with Resolution Enhancement Technology (REt) for
improved text)
●
50-sheet multipurpose tray (tray 1)
●
250-sheet enclosed input tray (tray 2)
●
Optional additional 250-sheet input tray (tray 3)
●
EconoMode
●
Print watermarks, booklets, multiple pages per sheet (N-up), and first page on different media than
the rest of the document
●
32 MB RAM
●
Memory can be upgraded to 288 MB
●
3,000-page or 7,000-page print cartridge
●
PCL 6, PCL 5e, and HP postscript level 3 emulation (printer automatically determines and switches
to the appropriate language)
●
Compatible with USB 2.0 specifications
●
Supported by Windows® 98 (printer driver only), Me (printer driver only), 2000, Server 2003 (printer
driver only), XP 32-bit, XP 64-bit (printer driver only)
●
Supported by Macintosh OS X V10.2.8, V10.3.9, V10.4.3
●
On/off switch
●
HP ToolboxFX (provides printer status information, troubleshooting information, and printer
configuration information)
●
Embedded Web server (EWS) with internal pages that are localized in 16 languages
●
46 HP fonts
●
35 HP postscript emulation level 3 fonts
HP LaserJet P2015d printer
The HP LaserJet P2015d printer includes all of the features of the HP LaserJet P2015 plus automatic two-sided (duplex) printing..


Download Free ebook HP LaserJet P2015 Series User Guide.Pdf

LEARN PRINTER REPAIR NO MATTER WHERE YOU ARE.Pdf

PDF Preview :

INSIDE THIS ISSUE

• HP LaserJet 5Si/8000/8100/8150 Online Training Course Released
• HP LaserJet 4000/4050/4100 Paper Feeder Control PCA
• Part Spotlight: Lexmark Optra E310 and E312 Right Side Gear Assembly
• Tech Tip: The HP LaserJet 2300 and Color LaserJet 2500 Separation Pad

HP LASERJET 5SI/8000/8100/8150
ONLINE TRAINING COURSE RELEASED


Online Training from Parts Now! is the same qual- ity instruction that our Director of Training Steve Geishirt gives in his hands-on classes, but from the comfort of your computer. And now, there’s even more reason to try Online Training, as we’ve just released the HP LaserJet 5Si/8000/8100/8150 course. There's no risk in trying out online training, because our intro course doesn't cost anything! You can take the first section of our basic course, Image Formation for HP Printers, for free. If you like that, we'll let you take the other four sections for free also—all you have to do is contact your account rep-resentative. We’ll take it from there!...


Download Free ebook LEARN PRINTER REPAIR NO MATTER WHERE YOU ARE.Pdf

11 Steps to Guarantee You Make the Digg Front Page.Pdf

PDF Preview :

Digg is one of the most visited social network sites. It enables users to submit and meanwhile vote other interesting stories. Because it's one of the most visited social network sites people understood that they can get really good traffic if they have a really interesting story to show. By saying good traffic we are talking about thousands of visitors sent daily to your story and links followed by! In order to do such a thing you need some friends to vote and of course a interesting story.....

Write about Digg. Could a site be any more narcissistic? I think not. Digg likes itself so much that Paris Hilton looks about as humble as a Nun by comparison. People must be sitting at their computers going “OMG Look it’s a story about Digg!

Download Free ebook 11 Steps to Guarantee You Make the Digg Front Page.Pdf:

BMW D7 OWNERS MANUAL.pdf

PDF Preview :


BMW D7 OWNERS MANUAL~this manual was written on your behalf in an effort to help you enjoy your new BMW Marine Engine to the maximum. No marine engine, be it the best in the world, will perform at it’s best during a long life, without proper care and maintenance. Please read this manual carefully before you set out on the first trip with your new BMW Marine Engine.

For the practical boat owner, some maintenance procedures are described in this manual. Next to some jobs, you will find this marking which indicates that the work will require special tools as well as certain special knowledge. It is, therefore, recommended that your authorized BMW Marine Dealer complete these operations.


Table of contents of BMW D7 Owners Manual

* ENGINE DESCRIPTION
* INSTRUMENTS AND CONTROLS
* STARTING AND OPERATING
* SERVICE & MAINTENANCE
* FUEL SYSTEM
* LUBRICATION SYSTEM
* COOLING SYSTEM
* VALVE SYSTEM
* ELECTRICAL SYSTEM
* WINTER LAY UP AND RECOMISSION

Download Free ebook BMW D7 OWNERS MANUAL.pdf

AUDI A3 WORKSHOP MANUAL 2004.Pdf

PDF Preview :

AUDI A3 WORKSHOP MANUAL 2004~service manual has been prepared primarily for the purpose of assisting service personnel in providing effective service and maintenance of the Toyota Corolla. This manual includes procedures for maintenance, adjustment, removal and installation, disassembly and assembly of components, and troubleshooting.

Technical information should always be available to the foremen and mechanics, because their careful and constant adherence to the instructions is essential to ensure vehicle road-worthiness and safety. In addition, the normal basic safety precautions for working on motor vehicles must, as a matter of course, be observed.

Table of contents Audi A3 Workshop Manual

Mixture preparation - injection

* Servicing injection system
* General notes on self-diagnosis
* Safety precautions
* Rules for cleanliness
* Procedure to be followed prior to opening high-pressure injection system - take note of the following
* Technical data
* Overview - fitting locations
* Exploded view - intake manifold
* Exploded view - fuel rail
* Exploded view - air cleaner / engine cover panel
* Removing and installing engine cover panel with air filter element
* Removing and installing intake manifold with fuel rail
* Removing and installing injectors
* Checking initial fuel pressure (up to high-pressure pump)
* Checking fuel pressure and residual pressure (up to high-pressure pump)
* Exploded view - high-pressure fuel pump
* Removing and installing high-pressure fuel pump
* Wiring and component check with test box V.A.G 1598/42
* Renewing Motronic control unit J220
* Removing and installing Lambda probe G39 and Lambda probe heater Z19 before catalytic converter
* Removing and installing Lambda probe after catalytic converter G130 and Lambda probe 1 heater, after catalytic converter

Download Free ebook AUDI A3 WORKSHOP MANUAL 2004.Pdf

NISSAN TITAN SERVICE MANUAL 2004.Pdf

PDF Preview :

NISSAN TITAN SERVICE MANUAL 2004~This service manual has been prepared primarily for the purpose of assisting service personnel in providing effective service and maintenance of the Nissan Titan. This manual includes procedures for maintenance, adjustment, removal and installation, disassembly and assembly of components, and troubleshooting.

All information, illustrations and specifications contained in this manual are based on the latest product information available at the time of publication. If your car differs from the specifications contained in this manual, consult your Nissan dealer for information.

Table contents

* General Information
* Engine Mechanical
* Transmission
* Transfer
* Front Suspension
* Brake System
* Power Steering System
* Seat Belts
* Body, Lock & Security System
* Air Conditioner
* Starting & Charging System
* Maintenance

Download Free ebook NISSAN TITAN SERVICE MANUAL 2004.Pdf

Canon Digital Video Camera ZR/60.Pdf

PDF Preview :

Canon Digital Video Camera ZR/60~This video camera comes with a Rechargable battery as well as the ability to plug into a house hold power source. If you are going to video tape in a place where there is no power source, then it is important to make sure that the camera’s battery is charged before you begin video taping. It takes about 110 minutes to fully charge the battery for this camera.

The Video Cassette

(1) Video Cassette comes with each Camera. You can request additional tapes when you pick up your camera from the IT department if you believe that one tape is not going to be enough. If you are video taping and do find youself short and cannot make it back to the IT Department or the IT Department is closed, make sure you purchase tapes with this logo on it.

Wheelock College -- Information Technology -- Canon Digital Video-ZR/60 Documentation

2.With the Strap that has the Canon Logo on it facing you, insert the cassette into the camera with the Yellow Tape protection tab up and on the left hand side.

3.Push gently on the side and the Camera will automatically close the cassette and get it ready for video taping...


Download Free ebook Canon Digital Video Camera ZR/60.Pdf

Replacing the Focusing Screen on the Canon EOS 20D Digital SLR Camera.Pdf

PDF Preview :

This PDF gives step by step instructions for replacing the focusing screen on the
Canon EOS 20D digital SLR camera, with some illustrations.

INTRODUCTION

The focusing screen on the Canon EOS 20D digital SLR camera may be readily
changed in the field. Often this is desired in order to replace the factory screen
with an alternative screen having manual focusing aids, such as a split image prism
and/or a microprism field, or merely to replace a damaged screen.

The details, including the information on determining the proper orientation of the
new screen, are predicated on the installation of a new OEM screen or an “aftermarket” screen closely adhering to the configuration and dimensions of the
OEM screen. If you have a screen for which this is not so, please get the necessary
supplemental information from the manufacturer or distributor.

I understand that with some aftermarket screens, the shim installed at the factory
to properly position the focusing screen must be removed. If you have such a
screen, please get the necessary supplemental information from the manufacturer
or distributor.

Canon EOS 20D—Replacing the Focusing Screen

TOOLS AND MATERIALS

The following tools and materials are recommended for the procedure described by
this article:
• Clean washcloth, small cloth towel, etc.
• Sheet of white bond paper
• Scissors
• (Optional) One Pec Pad or equivalent (camera lens wipe)
• Small tweezers with smooth flat tips (be sure they have no sharp edges or
“burrs”)
• Round wood toothpick (must have fairly sharp point)
• Camera dust blower or ear syringe
• Small block of wood about the size of a small matchbox (or a matchbox)
• Replacement focusing screen
If a dental mirror is available, it is very helpful in studying the battle zone to get an appreciation of where the retaining frame latch is, and may be useful in the actual procedure.

Download Free ebook Replacing the Focusing Screen on the Canon EOS 20D Digital SLR Camera.Pdf

Canon EOS Digital Rebel XT Camera Recommended Settings & Notes.PDF

PDF Preview :

Canon EOS Digital Rebel XT Camera Recommended Settings & Notes~Shutter speed and F-stop. Depending on the level of ambient light in your office, you may wish to adjust the F-stop. To change, hold down the AV +/- button on the back of the camera while turning the main dial just behind the shutter button. Turning left will decrease the F-stop number and yield brighter pictures, turning right will increase the F-stop number and yield darker pictures.

2 Focusing. Press and hold shutter halfway to focus image. When image is in focus, the camera will beep and the red lights in the squares will blink. The area directly behind the blinking light is the center point from which the camera focuses, so it is best if this is in the center of your subject. Without releasing, press the shutter all the way down to freeze the image. NOTE: Especially for intraorals, make sure to rotate the ring flash uni around the lens 90 degrees so that the part of the flash here the wire connects does not block the camera’s AF
sensor.

Battery Kit. Dolphin includes a Lithium-Ion rechargeable battery and charger with your camera. Purchasing an additional battery and charger is recommended for extended camera use. Using the LCD display drains the battery life sooner.

4 Filtering the Lightbox. Due to the intensity of the flash bulb inside the lightbox, we recommend placing some type of filter over the bulb to prevent the backlight from overpowering the camera’s flash. We recommend using two standard C-fold paper towels. Coffee filters or regular roll-type paper towels also work.
Do not worry about fire hazards as the split-second flash inside the lightbox is not enough to generate enough heat to burn. If your background comes out yellow, use less filters; if you see a halo or whiteness obscuring the jaw line then add more filters...

Download Free ebook Canon EOS Digital Rebel XT Camera Recommended Settings & Notes.PDF

Digital Camera Setup Canon A570.Pdf

PDF Preview :

Most manuals make little sense till you have the camera in front of you and ready to go. Here is a short cut guide, below, with the key info. Don't spend too long trying to figure out any given instruction. Start pushing buttons on the camera as soon as you have a rough idea what the instructions are trying to say. If you spend too long reading the manual or these instructions without trying things out on the camera, you will go insane.

Batteries are installed. You are responsible for replacing these if needed. NOTE – Battery Compartment: Turn the camera upside down with the lens facing you. Pull the battery compartment ‘slide’ toward you and then to the right! If you just pull back, it will NOT open. Figure on a new set every few hours of operation. Alternatively, Ni-MH rechargeable batteries can be used if you have them. DO NOT use NiCd or regular, cheap, non alkaline batteries. If you remove the batteries from the camera for some time, it will probably forget your settings.

The memory card is installed. This will allow you about 30 pictures before having to download to your computer. The number of remaining frames is displayed at the bottom right.


Download Free ebook Digital Camera Setup Canon A570.Pdf

Sony VAIO VGX-XL201 Media Center PC Clean Install Guide.Pdf

PDF Preview :

Sony VAIO VGX-XL201 Media Center PC Clean Install Guide~In their efforts to make life easier for novice PC users, Sony inadvertently make the process of escaping from the factory installed image difficult, even for competent PC users. They create a hidden partition on the hard disk that contains the factory installed image and provide software to back up that partition to a pair of recordable DVDs. This makes it possible to dispense with the hidden partition and recover the disk space, and also provides the means by which you can extract the essential drivers and utilities that make a clean install possible. What Sony don’t do is give you an OEM operating system CD or any means to install an operating system other than by re-imaging the PC back to it’s factory default settings.

This guide is intended for anyone who, like me, wishes to install the operating system of their choice without the software baggage that comes with the factory installed image. It goes into enough detail that a novice user should be able to follow it, but it is really intended for intermediate to advanced PC users. If you don’t know what you’re doing, you could get yourself into a terrible mess by following this guide and of course it goes without saying that I accept absolutely no responsibility for any damage or inconvenience whatsoever resulting from the use of this guide. It is provided in the hope that it will be useful, but it’s use is entirely at your own risk. The guide will deal specifically with installing the Windows XP Media Center Edition 2005 operating system on a Sony VAIO VGX-XL201 Media Center PC. However, the concepts described in this guide are likely to be largely relevant to similar operating systems like Windows XP Professional, and media center PCs like the Sony VAIO VGX-XL202. When Windows Vista ships in January 2007 I will probably create a new version of this guide dealing specifically with that operating system for the VGX-XL201.

Download Free ebook Sony VAIO VGX-XL201 Media Center PC Clean Install Guide.Pdf

BMW 740i/iL Trunk Shock Replacement Procedure.Pdf

PDF Preview :

BMW 740i/iL Trunk Shock Replacement Procedure~The procedure took only about 30 minutes and was very easy. The outcome was excellent making the project well worth it and highly recommended.

Procedure:
non government
1. It is best to remove and replace one shock and then move to the other side. Without any shock the trunk will easily fall on your head. To be safe, you may want to prop the trunk lid so it cannot fall on your head. When I had one shock removed, the wind did blow the lid down on my head!
2. Begin with the driver side shock. I recommend this because it is slightly easier since the wiring/harness does not come into play.
3. First, remove the c-clip of the upper mount, but do not disconnect the shock from the pivot mount yet. Here is picture with c-clip already removed. Another tip, I suggest replacing since cheap, but regardless, when you attempt to remove try to cover the clip with a rag so it doesn’t go flying. Mine disappeared out in the yard somewhere.
4. The next step is to remove the lower mounting clip. This is accomplished by using a screwdriver to push the clip downward and off the shock.
5. Now the driver side shock can be removed. Simply pull the lower part straight out and pull the upper mount off the pivot shaft. Again, be careful here that the trunk stays up and not on your skull.
6. Next install the new drivers side trunk shock. But first clean off the upper mount shaft and the lower ball joint. It really isn’t necessary to grease these connections because the new shock comes with grease already in the part.

Download Free ebook BMW 740i/iL Trunk Shock Replacement Procedure.Pdf

BMW Motorcycles SA314 Siren Speaker Mounting Bracket Installation Guide.Pdf

PDF Preview :

BMW Motorcycles SA314 Siren Speaker Mounting Bracket Installation Guide~The SA314 speaker bracket mounts on the left side crash bar of your motorcycle. If you have a light mounted here, the bracket mounting screws may share some or all of the mounting holes.
1. Secure the mounting brackets to the SA314 speaker using the provided hardware. Make sure that the brackets are properly oriented before proceeding.
2. Now secure the bracket onto the motorcycle using the supplied mounting hardware as shown below.
3. Connect the speaker to your siren as outlined in your siren installation manual.

Note: Always be sure the siren is mounted so that the wires exit the bottom of the siren. This will position the siren’s drain hole on the bottom for proper drainage. IMPORTANT! Before returning the vehicle to active service, confirm the proper operation of this product, as well as all vehicle components/equipment.

Download Free ebook BMW Motorcycles SA314 Siren Speaker Mounting Bracket Installation Guide.Pdf

DUCATI 996 BATTLE SHIFTER.Pdf

PDF Preview :

DUCATI 996 BATTLE SHIFTER~The Power Shifter by Battle Factory is a lightweight, compact semi-automatic upshift system for bikes 600cc and up that provides quick, smooth shifts every time. Unlike other shifters that simply cut the electronic ignition, the Battle Shifter works by reducing current to the coil enough to stop ignition. This ensures that power keeps flowing to your gauges, eliminating annoying readout flashes and reducing overall system shock. The Power Shifter automatically adjusts the duration of the ignition cut to match RPM’s – longer cuts at low RPM’s and shorter ones at high RPM’s. The Power Shifter also features a DSR (Delayed Spark Return) System and 2nd Gear Helper Function. The DSR System waits a revolution after returning spark to the first bank of cylinders before returning spark to the second bank, greatly reducing transmission shock. The 2nd Gear Helper Function helps reduce the normal shock when shifting from 1st to 2nd gear by lengthening the ignition cut time (only applicable on street bikes that have neutral sensor). Best of all, the Battle Factory Power Shifter doesn’t require a battery like other shifters on the market.

The Battle Shifter automatically cuts out under 2,500 RPM’s to prevent engine stall during slow speeds and idle. It comes fully setup for your bike from the factory.

IMPORTANT:
To ensure the long life of your unit, please read all instructions carefully. Check that the adjustment window is covered before riding!! Take care to ensure that all wires are connected correctly, especially the <+> and <–> as incorrect installation can result in damage to the unit. Be sure to ground the shifter’s <–> (black wire) to the frame.

Avoid installing the control unit in places where it will be exposed to excessive water, heat, dust or vibration. Also avoid securing it the close proximity of the ignition coil or plugs as electronic noise could interfere with normal operation. We recommend installing it in a convenient spot near the CDI on the meter stay. Be sure to insert the included sponge under the control unit before securing with the provided zip straps.

Download Free ebook DUCATI 996 BATTLE SHIFTER.Pdf

Hummer H2 Spare Tire Cover Installation Instructions.Pdf

PDF Preview :

Hummer H2 Spare Tire Cover Installation Instructions~Installation Procedures:
1. Standard black ABS faceplate must be painted. Your local auto parts store or body shop will be able to provide assistance with obtaining the correct type and match of paint. To paint faceplate:
a. Clean faceplate with a soap and water solution to remove dirt and other contaminates.
b. Sand painting surface with 320 grit sand paper.
c. Apply a coating of ABS compatible primer-adhesion promoter
d. Apply paint compatible with ABS as directed by the paint manufacturer
2. Hold the retaining ring over spare tire with trim facing towards you (latch assembly will be facing down). Place one side of the open end of the ring over the tire and gradually move ring over and around tire until the retaining ring fits over spare tire.
3. Carefully slip the painted faceplate between the tire and stainless retaining ring. Start at the top tire and work down each side, working retaining ring over faceplate edge.
4. Carefully close opening at bottom of the retaining ring, keeping the faceplate centered. Adjust the latch so the retaining ring fits snug.
5. If faceplate is loose, push on retaining ring edge to adjust the retaining ring inward to sandwich faceplate between tire and retaining ring.

Download Free ebook Hummer H2 Spare Tire Cover Installation Instructions.Pdf

BMW SRI Manual Reset 2001.Pdf

PDF Preview :

"BMW SRI Manual Reset 2001"~On 2001 vehicles without the diagnostic connector in the engine compartment, the use of the SIA reset tool is not possible. The service indicator may be reset using the reset mode in the instrument cluster.

Reset procedure for high and low clusters with SIA III using the Reset Mode:
• Ignition key must be “off”
• Press and hold the trip odometer reset button in the instrument cluster (left button), and turn the ignition key to the first position.
• Keep the button pressed for approximately 5 seconds until one of the following words appear in the display: “OIL SERVICE, or “INSPECTION”, with “RESET”.
The service due is shown with “reset” if the coded minimum consumption limit has been reached and resetting is possible. If “reset” is not shown, the minimum limit has not been reached and resetting is not possible.
• Press and hold the reset button again until the word “RESET” begins to flash.

Download Free ebook BMW SRI Manual Reset 2001.Pdf

INSTALLATION INSTRUCTIONS 2002 Dodge Ram 4.7L.Pdf

PDF Preview :

Below the detail content for this INSTALLATION INSTRUCTIONS 2002 Dodge Ram 4.7L manual PDF:
#300-567 INSTALLATION INSTRUCTIONS 2002 Dodge Ram 4.7L
Parts List
(1) Power Plate
(1) “O” Ring
(3) 6mm x 60mm Bolts
(3) 6mm Flat Washers
(3) Extension Plates (Short)
(2) Extension Plates (Long)
(5) 6mm x 20mm Flat Head Screws
(1) Air Box Flange Nut
(1) Air Box Extension Plate
(1) 5/16″ x 1 1/2″ Flat Head Screw

Tools List

3mm Hex Key
10mm Socket
10mm Box Wrench
Standard Screwdriver
Also available for your Dodge Ram, the AirAid Intake System, p/n 300-125-1. Call for details! Thank you for purchasing the PowerAid Throttle Body Spacer. Please read the instruction manual carefully before proceeding with the installation. Contact AIRAID @ (800) 498-6951 8:00 AM - 5:00 PM MST Weekdays for questions regarding fit or instructions that are not clear to you. Your PowerAid Throttle Body Spacer was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, please contact AIRAID.
Thank you for selecting AIRAID.2
Installation Instructions. Read Me!
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air intake assembly.
3. Remove throttle body intake box and save bolts.
4. Remove (3) bolts from throttle body.
5. Remove bolts from throttle linkage bracket and save.
6. Install power plate using (3) 6mm x 60 bolts and (3) 6mm flat washers. (Ref. “A”)
7. Locate (3) extension plates (short) and (3) 6mm x 20mm flat head screws before installing throttle linkage and dipstick bracket.
* Please Note: Remove the stud from front throttle linkage mount. The dipstick must be located under forward extension plate at flathead screw location.
8. Locate (2) extension plates (long) using (2) 6mm x 20mm flat head screws to reposition the throttle body intake box using saved bolts. Refer to Step 3.
9. Install air box extension plate using flange nut and 5/16″ flat head screw. (Ref. “E”)

Download Free ebook INSTALLATION INSTRUCTIONS 2002 Dodge Ram 4.7L.PDF

Kobol 1.4.0 User Manual.Pdf

PDF Preview :

Kobol is unique in the world of COBOL development systems. Kobol will generate a true executable with no run time requirements other than its support libraries. Kobol has a sophisticated IDE that contains extensive project management capability with integrated CVS support for revision management, syntax highlighting, an optional debugger and integrated syntax reference manual. The application is very straight forward to use with a low learning curve. This manual is arranged in a fashion to make it as quick and easy as possible to get started with Kobol.

When you purchased Kobol you received versions for both Windows and Linux. This chapter will explain how to install Kobol and its various subsystems. If you’re reading this document you should already have Kobol, but if you don’t, you can download a demo or purchase a copy at http://www.thekompany.com/products/kobol/. When you purchase Kobol you are entitled to free electronic updates for the life of the product for all supported platforms, this does not include add-on modules that are available separately.

You will need to be running a 300Mhz or better processor with at least 64MB of RAM, and either a Linux or MS Windows operating system. Koobl for Linux has been statically linked with all the libraries required, so you don’t need to worry about installing anything else for Kobol - just run it.

If you are using a Linux system then you need to unpack the Kobol installation package into whatever directory you like (we recommend /usr/local), by using the tar command: tar -zxvf Kobol-1.0.0.tar.gz or tar -jxvf Kobol-1.0.0.tar.bz2 Please note that the version number will change with each release, so the file name may not match the example. The command creates the directory Kobol-1.0.0 and puts all the files there. Now go into the directory with the following command: cd Kobol-1.0.0 Now just run installation script as root: ./install.sh If you have tried to install as a user other than ‘root’, then you will receive a warning message. The installation script will tell you where the files are installed so if you want to remove Kobol from your Linux system you will only need to remove /usr/local/kobol directory and the binary file /usr/bin/kobol.

Keep in mind that certain Linux distributions do not come with the required development libraries, currently that would be Lindows and Xandros. They are geared for a home desktop user and as such they don’t by default include developer tools like the gcc compiler.

To install Kobol on a Windows system you need to run the exe installation file. Now just follow the prompts as you would with any other Windows installer. If you select a ‘typical’ installation, then not all features will be installed. If you select a ‘full’ installation, you can disable features later if you like with ‘Control Panel->Removing and Add Programs’. It is also necessary for you to install the ‘CygWin’ application, this contains the compiler and various other pieces needed on Windows.

Download Free ebook Kobol 1.4.0 User Manual.Pdf

Ferrari GTO User Manual.pdf

PDF Preview :

Ferrari GTO was based on the mid-engined 308 GTB. The 288 refers to its 2.8 liter V8 engine, though, as it used a de-bored (by 1 mm) V8 with twin IHI turbochargers, intercoolers, and Weber-Marelli fuel injection.

Download Free ebook Ferrari GTO User Manual.pdf

Programming ASP.NET AJAX: Build rich, Web 2.0-style UI with ASP.NET AJAX .pdf

PDF Preview :

Delivering rich, Web 2.0-style experiences has never been easier. This book gives you a complete hands-on introduction to Microsoft ASP.NET AJAX 1.0, the new framework that offers many of the same benefits for Ajax development that ASP.NET provides for server-side development. With Programming ASP.NET AJAX, you'll learn how to create professional, dynamic web pages with Ajax in no time. Loaded with code and examples that demonstrate key aspects of the framework, this book is ideal not only for ASP.NET developers who want to take their applications a step further with Ajax, but for any web developers interested in ASP.NET AJAX, no matter what technology they use currently. That includes JavaScript programmers who would like to avoid the headaches of writing cross-browser code. Programming ASP.NET AJAX offers you: A high-level overview of the ASP.NET AJAX framework Functional code that you can cut and paste for use in your own applications The essentials of JavaScript and Ajax to help you understand individual technologies used by the framework An organization that reflects the framework's packages, including Extensions, Control Toolkit, the Futures CTP, and the AJAX Library Sidebars throughout the book that identify and propose solutions to potential security breaches Ways to use the standards-based AJAX Library with other platforms, such as PHP A complete chapter on the Update Panel control for making individual parts of a web page independently updateable -- one of the framework's most important elements Released previously as Programming Atlas to cover the beta version of the Microsoft framework, this edition is fully up-to-date and expanded for the official 1.0 release of ASP.NET AJAX. Written by Christian Wenz -- Microsoft MVP for ASP/ASP.NET and AJAX Control Toolkit Contributor -- Programming ASP.NET AJAX contains many hard-to-find details, along with a few unofficial ways to accomplish things.

Download Free ebook Programming ASP.NET AJAX: Build rich, Web 2.0-style UI with ASP.NET AJAX.Pdf

Application Development With Visual FoxPro 6 0.Pdf

PDF Preview :

Data Environment Overview The most common reason to build forms is to display and update the data in the application. Before you start building forms, you have to understand how forms work with data. Forms use the Data Environment to integrate data into a form. The Data Environment contains information about all the tables, relationships, and views, used by a form or report. When you save a form or report, the Data Environment information is saved with it. The Data Environment is modified in the Data Environment Designer. When the Data Environment of a form or report is defined, specifying .T. in the AutoOpenTables and AutoCloseTable properties instructs Visual FoxPro to open the tables or views when you open or run the file and close them when the file is closed or released.

Download Free ebook Application Development With Visual FoxPro 6 0.Pdf