PDF Preview :
"BMW SRI Manual Reset 2001"~On 2001 vehicles without the diagnostic connector in the engine compartment, the use of the SIA reset tool is not possible. The service indicator may be reset using the reset mode in the instrument cluster.
Reset procedure for high and low clusters with SIA III using the Reset Mode:
• Ignition key must be “off”
• Press and hold the trip odometer reset button in the instrument cluster (left button), and turn the ignition key to the first position.
• Keep the button pressed for approximately 5 seconds until one of the following words appear in the display: “OIL SERVICE, or “INSPECTION”, with “RESET”.
The service due is shown with “reset” if the coded minimum consumption limit has been reached and resetting is possible. If “reset” is not shown, the minimum limit has not been reached and resetting is not possible.
• Press and hold the reset button again until the word “RESET” begins to flash.
Download Free ebook BMW SRI Manual Reset 2001.Pdf
Showing posts with label manual. Show all posts
Showing posts with label manual. Show all posts
Monday, February 9, 2009
Tuesday, January 13, 2009
TUNING INSTRUCTIONS For Harley-Davidson Carburetors.Pdf
Content Preview :
TUNING INSTRUCTIONS For Harley-Davidson Carburetors ©2003 Edelbrock Corporation Brochure No. 63-0195 Rev. 8/03 INSTALLATION PROCEDURE Please study these instructions carefully before installing your new Edelbrock carburetor. This tuning manual is for Harley Davidson only! If you have any questions or problems, please call our Technical Hotline at: 1-877-888-7504 ext. 2, 8:00 am to 5:00 pm, Monday - Friday, Pacific Standard Time or e-mail us at edelbrock.edelbrock.com. The Edelbrock Performer Series Carburetor has five (5) adjustments: 1. IDLE SPEED: Mechanical, raises and lowers slide to preferred idle RPM. 2. IDLE MIXTURE (900-1200rpm): Controlled by air bleed. 3. MID RANGE (1300-3500rpm): Controlled by needle setting/size. 4. FULL RANGE (3600-6000rpm): Controlled by main jet. 5. ACCELERATOR PUMP (Off Idle Throttle Response): Controlled by bypass screw on float bowl. THROTTLE CABLE REQUIREMENTS NOTE: Edelbrock Performer Series carburetors require the use of a two-cable (push-pull) throttle assembly and cables. Quick Kits and Complete Kits include throttle cable adaptors for use with
Download Free ebook TUNING INSTRUCTIONS For Harley-Davidson Carburetors.Pdf
TUNING INSTRUCTIONS For Harley-Davidson Carburetors ©2003 Edelbrock Corporation Brochure No. 63-0195 Rev. 8/03 INSTALLATION PROCEDURE Please study these instructions carefully before installing your new Edelbrock carburetor. This tuning manual is for Harley Davidson only! If you have any questions or problems, please call our Technical Hotline at: 1-877-888-7504 ext. 2, 8:00 am to 5:00 pm, Monday - Friday, Pacific Standard Time or e-mail us at edelbrock.edelbrock.com. The Edelbrock Performer Series Carburetor has five (5) adjustments: 1. IDLE SPEED: Mechanical, raises and lowers slide to preferred idle RPM. 2. IDLE MIXTURE (900-1200rpm): Controlled by air bleed. 3. MID RANGE (1300-3500rpm): Controlled by needle setting/size. 4. FULL RANGE (3600-6000rpm): Controlled by main jet. 5. ACCELERATOR PUMP (Off Idle Throttle Response): Controlled by bypass screw on float bowl. THROTTLE CABLE REQUIREMENTS NOTE: Edelbrock Performer Series carburetors require the use of a two-cable (push-pull) throttle assembly and cables. Quick Kits and Complete Kits include throttle cable adaptors for use with
Download Free ebook TUNING INSTRUCTIONS For Harley-Davidson Carburetors.Pdf
Tuesday, January 6, 2009
Parts and Accessories Installation Instructions Pdf
Content Preview :
Parts and Accessories. Installation Instructions. DVD Navigation System Retrofit with On-Board Monitor BMW 3 Series Coupé (E 46/2) BMW 3 Series Saloon (E 46/4) These installation instructions are only valid for cars with SA 534 (automatic air conditioning) and SA 550 (on-board computer). Retrofit kit No. 65 90 0 391 113 Installation time The installation time is approx. 5.5 hours, but this may vary depending on the condition of the car and the equipment in it. Important information These installation instructions are primarily designed for use within the BMW dealership organisation and by authorised BMW service companies. In any event the target group for these installation instructions is specialist personnel trained on BMW cars with the appropriate specialist knowledge. All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and work instructions in a rational order using the prescribed tools (special tools) and observing current health and safety regulations.
Download Free ebook Parts and Accessories.Installation Instructions.Pdf
Parts and Accessories. Installation Instructions. DVD Navigation System Retrofit with On-Board Monitor BMW 3 Series Coupé (E 46/2) BMW 3 Series Saloon (E 46/4) These installation instructions are only valid for cars with SA 534 (automatic air conditioning) and SA 550 (on-board computer). Retrofit kit No. 65 90 0 391 113 Installation time The installation time is approx. 5.5 hours, but this may vary depending on the condition of the car and the equipment in it. Important information These installation instructions are primarily designed for use within the BMW dealership organisation and by authorised BMW service companies. In any event the target group for these installation instructions is specialist personnel trained on BMW cars with the appropriate specialist knowledge. All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and work instructions in a rational order using the prescribed tools (special tools) and observing current health and safety regulations.
Download Free ebook Parts and Accessories.Installation Instructions.Pdf
Apple iPod 3rd Generation Take Apart Repair Manual Pdf
Content Preview :
Top Case Removal 3 Headphone Jack Board Removal 5 Hard Drive Removal 8 Hard Drive Cable Removal 9 Logic Board Removal 10 Battery Removal 12 LCD Removal 13 TouchWheel Cable Removal 14. Apply enough pressure so that your flat tool does not slip and scratch your iPod. Note that there is an orange cable in the top left corner that connects the iPod logic board to the headphone ports. Pull the headphone port out of the iPod. You may have to pull a little around the orange foil shield to release it from its adhesive backing.
Download Free ebook Apple iPod 3rd Generation Take Apart Repair Manual.Pdf
Top Case Removal 3 Headphone Jack Board Removal 5 Hard Drive Removal 8 Hard Drive Cable Removal 9 Logic Board Removal 10 Battery Removal 12 LCD Removal 13 TouchWheel Cable Removal 14. Apply enough pressure so that your flat tool does not slip and scratch your iPod. Note that there is an orange cable in the top left corner that connects the iPod logic board to the headphone ports. Pull the headphone port out of the iPod. You may have to pull a little around the orange foil shield to release it from its adhesive backing.
Download Free ebook Apple iPod 3rd Generation Take Apart Repair Manual.Pdf
Sunday, January 4, 2009
Dodge 8W-97 Power Distribution Service Manual Pdf
Content Preview :
The power distribution system for this vehicle consists of the following components: • Cigar Lighter Outlet • Front Control Module (FCM) • Integrated Power Module (IPM) • Power Distribution Center (PDC) • Power Outlets Refer to Wiring Diagrams for complete circuit schematics. The power distribution system also incorporates various types of circuit control and protection features, including: • Automatic resetting circuit breakers • Blade-type fuses • Cartridge fuses • Relays. The power distribution system for this vehicle is designed to provide safe, reliable, and centralized distribution points for the electrical current required to operate all of the many standard and optional factory-installed electrical and electronic power train, chassis, safety, security, comfort and convenience systems. Integrated power module : The Integrated Power Module (IPM) is a combination of the Power Distribution Center (PDC) (1) and the Front Control Module (FCM) (2). The IPM is located in the engine compartment, next to the battery. Removal Guide : Disconnect the negative and positive battery cables. Unsnap cover and remove the B+ terminal nut from the integrated power module (IPM). Remove the B+ cable. Installation Guide : Install the Front Control Module (FCM) (2) to the Integrated Power Module (IPM). Install the B+ cable and nut on the IPM B+ terminal. Snap the cover in place. IOD Fuse : All vehicles are equipped with an Ignition-Off Draw (IOD) fuse that is disconnected within the Integrated Power Module when the vehicle is shipped from the factory. Dealer personnel are to reconnect the IOD fuse in the Integrated Power Module as part of the preparation procedures performed just prior to new vehicle delivery. The term ignition-off draw identifies a normal condition where power is being drained from the battery with the ignition switch in the Off position. The IOD fuse feeds the memory and sleep mode functions for some of the electronic modules in the vehicle as well as various other accessories that require battery current when the ignition switch is in the Off position.
Download Free ebook Dodge 8W-97 Power Distribution Service Manual.Pdf
The power distribution system for this vehicle consists of the following components: • Cigar Lighter Outlet • Front Control Module (FCM) • Integrated Power Module (IPM) • Power Distribution Center (PDC) • Power Outlets Refer to Wiring Diagrams for complete circuit schematics. The power distribution system also incorporates various types of circuit control and protection features, including: • Automatic resetting circuit breakers • Blade-type fuses • Cartridge fuses • Relays. The power distribution system for this vehicle is designed to provide safe, reliable, and centralized distribution points for the electrical current required to operate all of the many standard and optional factory-installed electrical and electronic power train, chassis, safety, security, comfort and convenience systems. Integrated power module : The Integrated Power Module (IPM) is a combination of the Power Distribution Center (PDC) (1) and the Front Control Module (FCM) (2). The IPM is located in the engine compartment, next to the battery. Removal Guide : Disconnect the negative and positive battery cables. Unsnap cover and remove the B+ terminal nut from the integrated power module (IPM). Remove the B+ cable. Installation Guide : Install the Front Control Module (FCM) (2) to the Integrated Power Module (IPM). Install the B+ cable and nut on the IPM B+ terminal. Snap the cover in place. IOD Fuse : All vehicles are equipped with an Ignition-Off Draw (IOD) fuse that is disconnected within the Integrated Power Module when the vehicle is shipped from the factory. Dealer personnel are to reconnect the IOD fuse in the Integrated Power Module as part of the preparation procedures performed just prior to new vehicle delivery. The term ignition-off draw identifies a normal condition where power is being drained from the battery with the ignition switch in the Off position. The IOD fuse feeds the memory and sleep mode functions for some of the electronic modules in the vehicle as well as various other accessories that require battery current when the ignition switch is in the Off position.
Download Free ebook Dodge 8W-97 Power Distribution Service Manual.Pdf
Mitsubishi Eclipse Clutch Overhaul Pdf
Content Preview :
The clutch overhaul guide for Mitsubishi eclipse, removal and installation, clutch inspection, clutch release cylinder, di-sassembly and re-assembly, Inspection, specification, fastener tightening, specifications, general specifications, service specifications, lubricants. Clutch exploded views and part list. Removal service point : Move the release fork in the direction shown to remove the clip from the fulcrum. Installation service point 1. "Apply Mitsubishi genuine grease part number 0101011 or equivalent to the illustrated positions of the release fork". 2. "Install the release fork to the fulcrum". Clutch disk and clutch cover installation 1. "Apply Mitsubishi genuine grease part number 0101011 or equivalent to the clutch disc splines and rub it in the splines with a brush". 2. "Using the clutch disc guide to position the clutch disc on the flywheel". 3. Install the clutch cover onto the flywheel. Outer race installation : Press in the bushing into the release fork to the position shown in the illustration. Release fork installation : Apply Mitsubishi genuine grease part number 0101011 or equivalent to the illustrated positions of the release fork. Sealing cap installation : Press in the sealing cap to the position shown in the illustration. Be sure that it is not installed in a slanted position. Clutch inspection : 1. Check the diaphragm spring end for wear and uneven height. Replace if wear is evident or height difference exceeds the limit. Limit: 0.5 mm (0.020 inch) 2. Check the pressure plate surface for wear, cracks and discoloration. 3. Check the rivets of the strap plate for looseness. If loose, replace the clutch cover. Don’t clean the clutch disc in a cleaning solvent. 1. Check the facing for loose rivets, uneven contact, evidence of seizure, or deposited oils and greases. If defective, replace the clutch disc. 2. Measure the rivet sink and replace the clutch disc if it is below the limit. Minimum limit: 0.3 mm (0.012 inch..
Download Free ebook Mitsubishi Eclipse Clutch Overhaul.Pdf
The clutch overhaul guide for Mitsubishi eclipse, removal and installation, clutch inspection, clutch release cylinder, di-sassembly and re-assembly, Inspection, specification, fastener tightening, specifications, general specifications, service specifications, lubricants. Clutch exploded views and part list. Removal service point : Move the release fork in the direction shown to remove the clip from the fulcrum. Installation service point 1. "Apply Mitsubishi genuine grease part number 0101011 or equivalent to the illustrated positions of the release fork". 2. "Install the release fork to the fulcrum". Clutch disk and clutch cover installation 1. "Apply Mitsubishi genuine grease part number 0101011 or equivalent to the clutch disc splines and rub it in the splines with a brush". 2. "Using the clutch disc guide to position the clutch disc on the flywheel". 3. Install the clutch cover onto the flywheel. Outer race installation : Press in the bushing into the release fork to the position shown in the illustration. Release fork installation : Apply Mitsubishi genuine grease part number 0101011 or equivalent to the illustrated positions of the release fork. Sealing cap installation : Press in the sealing cap to the position shown in the illustration. Be sure that it is not installed in a slanted position. Clutch inspection : 1. Check the diaphragm spring end for wear and uneven height. Replace if wear is evident or height difference exceeds the limit. Limit: 0.5 mm (0.020 inch) 2. Check the pressure plate surface for wear, cracks and discoloration. 3. Check the rivets of the strap plate for looseness. If loose, replace the clutch cover. Don’t clean the clutch disc in a cleaning solvent. 1. Check the facing for loose rivets, uneven contact, evidence of seizure, or deposited oils and greases. If defective, replace the clutch disc. 2. Measure the rivet sink and replace the clutch disc if it is below the limit. Minimum limit: 0.3 mm (0.012 inch..
Download Free ebook Mitsubishi Eclipse Clutch Overhaul.Pdf
Wednesday, December 31, 2008
MITSUBISHI Magna AWD Sedan Pdf
Content Preview :
Mitsubishi is marketing three versions of the new sedan and they are the Magna AWD, the Magna Sports AWD and the Verada AWD. All three are available with automatic transmission only; it’s Mitsubishi’s well- regarded five-speed tiptronic-style INVECS II ‘Sports Mode’ unit. Prices start at $37,490 for the base model; the Sports costs $43,290 and the Verada is priced at $46,460....
Download Free ebook MITSUBISHI Magna AWD Sedan.pdf
Mitsubishi is marketing three versions of the new sedan and they are the Magna AWD, the Magna Sports AWD and the Verada AWD. All three are available with automatic transmission only; it’s Mitsubishi’s well- regarded five-speed tiptronic-style INVECS II ‘Sports Mode’ unit. Prices start at $37,490 for the base model; the Sports costs $43,290 and the Verada is priced at $46,460....
Download Free ebook MITSUBISHI Magna AWD Sedan.pdf
Tuesday, December 30, 2008
2008 AutoCAD Architecture Pdf
Content Preview :
Key Features in AutoCAD Architecture Details Do documenting and annotating designs consume too much time? Complete these tasks faster with AutoCAD Architecture software’s robust library of detail components and powerful keynoting tools. Automate the creation of details and maintain consistent annotation. And when your details are complete, generate keynote legends with just a few clicks. Walls, Doors, and Windows Looking for a faster way to create and modify floor plans? Take advantage of walls, doors, and windows in AutoCAD Architecture to easily and quickly draw and document these common building elements. Automatically insert a door or window into a wall with complete placement control. Move a wall, and connected walls and spaces automatically update.
Download Free ebook AutoCAD Architecture 2008.Pdf
Key Features in AutoCAD Architecture Details Do documenting and annotating designs consume too much time? Complete these tasks faster with AutoCAD Architecture software’s robust library of detail components and powerful keynoting tools. Automate the creation of details and maintain consistent annotation. And when your details are complete, generate keynote legends with just a few clicks. Walls, Doors, and Windows Looking for a faster way to create and modify floor plans? Take advantage of walls, doors, and windows in AutoCAD Architecture to easily and quickly draw and document these common building elements. Automatically insert a door or window into a wall with complete placement control. Move a wall, and connected walls and spaces automatically update.
Download Free ebook AutoCAD Architecture 2008.Pdf
Nissan R20 Starting and Charging System Workshop Manual Pdf
Content Preview :
.....Wiring Diagrams and Trouble Diagnoses. When you read wiring diagrams, refer to the following: “HOW TO READ WIRING DIAGRAMS”, “POWER SUPPLY ROUTING” for power distribution circuit When you perform trouble diagnoses, refer to the following: “HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES”. “HOW TO PERFORM EFFICIENT DIAGNOSIS FOR AN ELECTRICAL INCIDENT”. How to Handle Battery, METHODS OF PREVENTING OVER-DISCHARGE, CHECKING ELECTROLYTE LEVEL. How to Handle Battery Remove the cell plug using a suitable tool. Add distilled water up to the MAX level. Battery Test and Charging Chart, Chart Diagnosis. Visual Inspection. Check battery type and determine the specified current using the table shown above. After starting charging, adjustment of charging current is not necessary. Do not use standard charge method on a battery whose specific gravity is less than 1.100., Set charging current to value specified in Fig. 4. If charger is not capable of producing specified current value, set its charging current as close to that value as possible. Starting system Wiring Diagram. ZD30DDTi ENGINE MODELS, Starting system Construction (exploded views). Starting system inspection procedure : Magnetic Switch Check, Pinion/Clutch Check. Field Coil Check. Charge wiring diagram.
Download Free ebook Nissan R20 Starting and Charging System Workshop Manual.Pdf
.....Wiring Diagrams and Trouble Diagnoses. When you read wiring diagrams, refer to the following: “HOW TO READ WIRING DIAGRAMS”, “POWER SUPPLY ROUTING” for power distribution circuit When you perform trouble diagnoses, refer to the following: “HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES”. “HOW TO PERFORM EFFICIENT DIAGNOSIS FOR AN ELECTRICAL INCIDENT”. How to Handle Battery, METHODS OF PREVENTING OVER-DISCHARGE, CHECKING ELECTROLYTE LEVEL. How to Handle Battery Remove the cell plug using a suitable tool. Add distilled water up to the MAX level. Battery Test and Charging Chart, Chart Diagnosis. Visual Inspection. Check battery type and determine the specified current using the table shown above. After starting charging, adjustment of charging current is not necessary. Do not use standard charge method on a battery whose specific gravity is less than 1.100., Set charging current to value specified in Fig. 4. If charger is not capable of producing specified current value, set its charging current as close to that value as possible. Starting system Wiring Diagram. ZD30DDTi ENGINE MODELS, Starting system Construction (exploded views). Starting system inspection procedure : Magnetic Switch Check, Pinion/Clutch Check. Field Coil Check. Charge wiring diagram.
Download Free ebook Nissan R20 Starting and Charging System Workshop Manual.Pdf
Monday, December 29, 2008
Chevrolet Belt Noise Troubleshooting Guide Pdf
Content Preview :
Chevrolet Belt Noise ..All is quiet in the engine compartment. The customer pays the invoice and all seems well. Weeks later, the belt chirp noise returns and so does the customer. The technician warranties the belt, eliminating the belt noise condition. When the noise symptom repeats it self, the service manager is ready to change belt suppliers. The odds are the vehicle has some problems inherent by design, or something is out of alignment. Unless the technician takes the time to accurately diagnose the reason for the noise condition, the symptom will continue to plague the system. For a belt noise condition, the first check should involve a belt-to-pulley alignment check. Verify that the power steering pump pulley is pressed onto the pump shaft in the proper position. While the pulley should be flush with the end of the pump shaft, it can be repositioned on the shaft to achieve the proper belt alignment. Vehicles produced after June 2004 have the revised AC/power steering pump mounting bracket. The rear power steering mounting bracket on all vehicles prior to and after the mentioned production date may require a modification. This modification involves drilling larger holes into the rear mounting bracket to ensure proper alignment when installing the mounting bolts. GM TSB 05-06-01-018 illustrates the proper procedure and necessary mounting bracket part number, where applicable. Chrysler acknowledges that a belt chirping or squeaking condition may be present on the 2004–2005 Pacifica with the 3.5L engine, due to misaligned pulleys.
Download Free ebook Chevrolet Belt Noise Troubleshooting Guide.Pdf
Chevrolet Belt Noise ..All is quiet in the engine compartment. The customer pays the invoice and all seems well. Weeks later, the belt chirp noise returns and so does the customer. The technician warranties the belt, eliminating the belt noise condition. When the noise symptom repeats it self, the service manager is ready to change belt suppliers. The odds are the vehicle has some problems inherent by design, or something is out of alignment. Unless the technician takes the time to accurately diagnose the reason for the noise condition, the symptom will continue to plague the system. For a belt noise condition, the first check should involve a belt-to-pulley alignment check. Verify that the power steering pump pulley is pressed onto the pump shaft in the proper position. While the pulley should be flush with the end of the pump shaft, it can be repositioned on the shaft to achieve the proper belt alignment. Vehicles produced after June 2004 have the revised AC/power steering pump mounting bracket. The rear power steering mounting bracket on all vehicles prior to and after the mentioned production date may require a modification. This modification involves drilling larger holes into the rear mounting bracket to ensure proper alignment when installing the mounting bolts. GM TSB 05-06-01-018 illustrates the proper procedure and necessary mounting bracket part number, where applicable. Chrysler acknowledges that a belt chirping or squeaking condition may be present on the 2004–2005 Pacifica with the 3.5L engine, due to misaligned pulleys.
Download Free ebook Chevrolet Belt Noise Troubleshooting Guide.Pdf
Subscribe to:
Posts (Atom)